Beaded bracelet instructions: Square bead checkerboard bracelet kit

You will be able to but the kit for this bracelet in a day or two. I’ve made all the kits, just need to get it into our shopping cart. But meanwhile, I am uploading the pattern to this blog for those of you who would like to put together your own kit.

Instructions for Making a Checkerboard Square Bead Bracelet using the Mirrix Loom

Materials Included for making one bracelet:
Matte Patina Iris
Matte Metallic Khaki Iris
Metallic Gold Iris
Two swarovski pearlized crystals
Six grams of Japanese seed beads: Matte Metallic Kahaki Iris
One bobbin of C-lon beading thread
Hand-dyed silk yarn for finishing

Necessary tools not included in the kit:

A Mirrix Loom with or without a shedding device
A piece of cloth for holding beads; a beading needle, a blunt edge needle

Warping your Mirrix Loom:

Warp Coil size: 18 dents (a 14 or 16 dent coil will also work)
Number of warps: 13
Number of rows for 6 ¾ inch bracelet: 99

You can use any of the Mirrix Looms to create this lovely bracelet. This piece can be woven with or without the shedding device. It’s your choice. Try Both!

These instructions are for a bracelet 6 ¼ inches in diameter when on your wrist. Increase or decrease by three rows to add or subtract a quarter inch from the size of your bracelet. Make sure that there are sixrows after the button hole.

You will want to reduce your loom’s height to minimize the amount of warp you will use. If you have a larger Mirrix Loom, this can be accomplished by using the extra warping bar. Use the 18 dent coil for this project if possible. The 14 or 16 dent coils will also be adequate. You will need to have 13 warp threads.

We have included a bead pattern to demonstrate the placement of colors. This pattern does not reflect the actual colors included in this kit. Do follow the placement of color in the pattern.

To Begin Weaving:

Place three piles of the different colored cylinder beads on a cloth in front of your loom.

Cut a length of C-lon thread about a yard long. Tie the end of this thread to the bottom of the left threaded rod on your loom using a slip knot so that you can easily release it and weave it back into your piece later. Beginning with the first row, pick up three blue/green beads, three gold beads, three blue/green beads and three gold beads. Weave these beads. Repeat this pattern for two more rows. The next row will comprise three green beads, three gold beads, three green beads and three gold beads. Repeat for two rows. The next row will comprise three gold beads, three blue/green beads, three gold beads, three blue/green beads. Continue this pattern of for 93 rows for a 6 ¾ inch bracelet. As I mentioned before, add or subtract three bead rows to add or subtract a quarter of an inch to your bracelet. Some adjustment can be accomplished by the placement of your peyote button.

For the next section, keep the new color and replace the old color for nine rows. At row 94, you will need to create a button hole. Continue weaving with your current thread, but only go to column six (please see white line in enclosed pattern). Weave this section of only six columns for six rows. Start a new thread to weave the five columns on the other side of the bracelet. Weave that side for six rows. End one of the threads and continue weaving a straight row of checkerboard for six rows.

Next you need to weave in a header and a footer with the silk thread. Cut the thread in half. Thread a blunt nose tapestry needle. You will be weaving a half inch of this silk on either end of the bracelet. Using the needle, go under and over every other thread (or pairs of threads, if you have used the shedding device), then reverse direction and go under the threads you went over and over the threads you went under. After you have woven a half inch, sew both ends of the silk thread into the woven part so it does not ravel. When you’ve finished weaving your header and footer, loosen the tension on your loom and slip out the warping bar. Lay your piece flat and trim the ends so that you have at least four inches left to work with. Tie overhand knots with warp pairs. When you’ve tied all the knots, trim the warp as close as you can without allowing the knots to be undone. Fold the header (or footer) at the seam where the header and beads meet. Turn the knots under so that they are buried. Carefully sew this header down so that you knots are buried and it looks neat. Do the same with the footer. This will be the back of your bracelet. You want to make this hem as sturdy and neat as possible. Make sure that you avoid covering the button hole.

In order to add a picot edge to the sides of the bracelet, string a workable length of C-lon (a yard) and sew it through the beads at one end of the bracelet in order to firmly attach it. You will pass your needle through the last bead at the edge of the bracelet, pick up three 11/0 seed beads and then pass back through the next edge bead. Pass your needle through the next bead so that you are once again working on the edge of the bracelet. String three more seed bead and pass back through next bead. Continue this way until you have come to the end of the bracelet. If you have left over C-lon, work your way back to the other side of the bracelet and repeat this procedure until you’ve reached the far end. If you have only a short length of C-lon, string a new piece and firmly attach to bracelet. This edging is very attractive as well as reinforcing your bracelet and disguising the warp threads on the side of the bracelet.

The “button” will be created using peyote stitch:

Using cylinder bead color of your choice to make a flat peyote piece that you will sew into a cylinder. Firmly attach the pearls to either end of the tube.

String ten 11/0 seed beads. Make the piece 8 rows wide. Zip the first and last rows together to form a tube. Sew the tail back into the bead work. Use the left over thread to sew to the sixth bead in one of the rows. You will be sewing this button onto the bracelet at a point that creates the best fit for you. String up three 11/0 seed beads, sew onto bracelet, thread three cylinder beads, sew back through button.

Wear and enjoy!

Or, if this is a gift: put it in the included gift bag and give it away!

Mirrix Loom Homepage

About these ads

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s